Skip to content

Tight Driveway Fix

Bi-Folding Gates in Denver

A gate that folds in sections opens where a swing gate runs out of room, fast, motorized, and fully controlled.

  • LiftMaster & MyQ
  • UL 325 Compliant
  • Custom Fabricated
An ornate automatic black iron and wood gate with stone pillars at the entrance to a luxurious house, set on a paved driveway with mountains in the background.

What Goes Wrong

Where cheap or rushed folding gate installs fail

The folding mechanism only works correctly when the hardware, post work, and alignment are done right from the start.

Wrong Opener Size

An opener sized for a single-leaf gate strains under the combined panel weight of a bi-fold system and fails early.

Weight-Matched Hardware

Partners size the opener and mounting hardware to the actual combined panel weight before any equipment is ordered.

Skipped Site Check

Installing without checking slope and post condition leads to a gate that drags, sticks, or binds mid-cycle within months.

Full Site Assessment

Driveway width, slope, clearance, and post condition are all confirmed before hardware selection begins.

Misaligned Sensors

Safety sensors set at the wrong height or angle fail to interrupt the cycle, creating a collision risk with vehicles and people.

UL 325 Sensor Setup

Sensors are aligned at both travel limits and tested to UL 325 requirements so the gate stops correctly every cycle.

Poor Hinge Setting

Hinges set out of plane cause the two leaves to fight each other, producing noise, uneven wear, and a gate that never closes flush.

Cycle-Tested Alignment

Both leaves are aligned so they fold and return in one smooth arc, confirmed by a full opening and closing cycle test.

What’s Included

Everything a bi-folding gate install covers

From the gate panels and posts to the opener, controls, and safety sensors, the full scope in one coordinated job.

Sloped Driveway Assessment

Slope and clearance check before hardware is selected.

Gate Alignment & Cycle Test

Full open-close test confirms travel limits and sensor response.

Opener Mounting Hardware

Brackets and hardware sized to the panel weight.

Tight Driveway Fix

A folding gate opens where a swing gate runs out of room

The bi-folding mechanism solves the clearance problem without sacrificing a motorized entry.

Request a Quote

Older Denver neighborhoods with short driveway setbacks often have entries where a single-leaf swing gate would strike a parked car or a wall before it fully opens. A bi-folding gate splits the panel at a central hinge, so each leaf only travels half the arc. That smaller sweep fits entries that a standard swing gate cannot clear.

Post condition and slope are checked before any hardware is ordered. The opener mounting hardware and control box are sized to the combined panel weight, and the hinges are set so both leaves fold and return in a single smooth cycle. Safety sensors are aligned at the fully open and closed positions to meet UL 325 requirements.

After installation, the opening and closing cycle test confirms that the gate reaches its travel limits cleanly and that the safety sensors interrupt the cycle correctly if the path is blocked. Remote control and keypad access are programmed at the same visit so the entry is fully operational before the partner leaves the site.

Why Choose Us

Why Gate Install Denver for bi-folding gate work?

Accountability, vetted partners, and hardware standards that hold up on Denver’s sloped lots and tight entries.

Vetted Local Partners

We connect you with independent local specialists who have handled bi-folding gate installs on Denver driveways.

LiftMaster Operators Standard

Every motorized install uses LiftMaster operators with MyQ access, not unbranded hardware with no support chain.

UL 325 Safety Hardware

Partners install UL 325-compliant safety sensors on every job, so the gate meets the standard before you use it.

Custom-Fabricated Panels

Steel and aluminum panels are fabricated to your exact opening, not cut down from a stock size that almost fits.

Full-System Accountability

One point of contact covers panels, opener, sensors, and controls, no handoffs between separate contractors.

A large automated metal driveway gate with geometric design, flanked by brick pillars with lanterns, leading to a luxury house with mountains in the background.
A black and red automatic gate opener is installed on a concrete pad next to a stone and wood gate post, with an ornate black metal gate partially open.

How It Works

From first call to a gate that opens and closes correctly

Request a Quote

  1. 01

    Describe Your Driveway

    Share the opening width, slope, post condition, and access needs so we can match you with the right local partner.

  2. 02

    Site Assessment & Quote

    A partner visits to check clearance, slope, and post condition, then quotes the full system with hardware specified upfront.

  3. 03

    Install & Cycle Test

    Panels, opener, sensors, and controls are installed and confirmed with a full opening and closing cycle test before handover.

Pricing Estimates

Typical Bi-Folding Gates Prices

JobTypical cost
Residential bi-fold gate$3,800-$7,000
Steel bi-fold gate$5,000-$9,000
Wrought iron bi-fold gate$6,000-$11,000
These prices are estimates and often vary with the condition, size and scope of each job. Message or call us for a free, no-obligation quote.
See all prices

Common Questions

Questions about bi-folding gate installs in Denver

  • Will a bi-folding gate work on a sloped driveway?

    Often yes. The site assessment checks slope, clearance, and post condition before any hardware is ordered. Denver sloped lot properties are a common fit for this gate style precisely because the folding arc clears obstacles that would block a swing gate.

  • What hardware does a motorized folding gate need?

    A bi-folding gate needs an opener, mounting hardware, a control box, and safety sensors at minimum. Depending on the site, post setting, concrete work, or electrical runs may also be required. All of that is scoped at the site visit.

  • What happens if I delay replacing a gate that sticks or drags?

    A gate that binds mid-cycle puts repeated strain on the opener motor. That shortens the motor’s service life and can cause the gate to stop in a half-open position, leaving the entry unsecured. The longer the cycle runs out of alignment, the more components need replacing.

  • Is a bi-folding gate the same as a regular swing gate?

    No. A swing gate opens as one or two large leaves and needs full clearance in front of the driveway. A bi-folding gate folds in sections, cutting the clearance arc by roughly 50 percent. That difference is what makes it practical for tight or sloped entries.

  • Do the safety sensors meet any compliance standard?

    Yes. Partners align and test photo eyes to UL 325 requirements. That standard requires the gate to reverse or stop before striking a person or vehicle in the path. Sensors are tested at both the open and closed travel limits before the job is signed off.

  • Can I control the gate from my phone?

    Yes. LiftMaster operators with MyQ access are standard on motorized installs. MyQ lets you open, close, and monitor the gate remotely and check access logs from your phone. Remote controls and keypad entry are programmed at the same visit.

More questions about Bi-Folding Gates?

Tell Us About Your Entrance

Describe the driveway width, slope, and access needs and we’ll connect you with a local specialist who can price the full bi-folding gate system upfront.

Request a Quote